You can now highlight GT transceiver capable channels in the Quartus II Pin Finder.
Altera Quartus 13.1 Full Support ForNew Features and Enhancements The Quartus II software release version 15.0 includes the following new features and enhancements: Full support for the MAX 10 10M02 device.
![]() Improvements to the Quartus II Pin Planner; you can now highlight channels in the Pin Finder. Altera Quartus 13.1 Full Installation OfMemory Recommendations A full installation of the Quartus II software requires up to 24 GB of available disk space. Altera recommends that your system be configured to provide virtual memory equal to the recommended physical RAM that is required to process your design. These recommendations are based on the amount of physical memory required to achieve runtime within 10 of that achieved on hardware with an infinite amount of RAM. Table 1: Memory Requirements for Processing Designs These requirements are the same for both Windows and Linux installations. Family Device Recommended Physical RAM Arria II GX EP2AGX45 EP2AGX65 EP2AGX95, EP2AGX125, EP2AGX190 EP2AGX GB 4 GB 6 GB 2015 Altera Corporation. ALTERA, ARRIA, CYCLONE, ENPIRION, MAX, MEGACORE, NIOS, QUARTUS and STRATIX words and logos are trademarks of Altera Corporation and registered in the U.S. Patent and Trademark Office and in other countries. All other words and logos identified as trademarks or service marks are the property of their respective holders as described at Altera warrants performance of its semiconductor products to current specifications in accordance with Alteras standard warranty, but reserves the right to make changes to any products and services at any time without notice. Altera assumes no responsibility or liability arising out of the application or use of any information, product, or service described herein except as expressly agreed to in writing by Altera. Altera customers are advised to obtain the latest version of device specifications before relying on any published information and before placing orders for products or services. ISO 9001:2008 Registered Innovation Drive, San Jose, CA 95134 quartus directory. ![]() Workaround To run EyeQ in Arria 10 designs, select the Enable prbs soft accumulators option in the Native PHY IP core IP Parameter Editor. Quartus II Software and Device Support Release Notes Version 15.0 Altera Corporation. The voltage rails affected are: VCC VCCL VCCERAM VCCLHPS VCCIOREFHPS VCCPLLHPS Default VCCIO voltage for 10AX115 devices is incorrect in Quartus II software release version 13.1 Arria 10 Edition On the Voltage page of the Quartus II software, the default voltage listed for VCCIO (2.5 V) is incorrect. Altera Quartus 13.1 Update After RecompilationNetlist viewer does not refresh when the design is recompiled The Netlist Viewer will not update after recompilation if the Netlist Viewer window is open when you modify and recompile the design by double-clicking on Fitter in the Task pane on the left side of the Quartus II software. Workaround This issue is corrected in Quartus II software release version 14.0 Arria 10 Edition. This issue is corrected in Quartus II software release version 14.0 Arria 10 Edition. This issue is corrected in Quartus II software release version Table 4: Device Support Removed These device families are no longer supported by the Quartus II software. Last Supported in. Cyclone III Stratix III Arria GX Cyclone, Cyclone II MAX 3000A, MAX 7000A, MAX 7000AE, MAX 7000B, MAX 7000S HardCopy II, HardCopy III, HardCopy IV Stratix, Stratix GX, Stratix II, Stratix II GX Related Information Altera Knowledge Base For more information about known device issues and workarounds. Altera Corporation Quartus II Software and Device Support Release Notes Version 15.0. Refer to the Quartus II Default Settings File (.qdf), quartusbinassignment defaults.qdf, for a list of all the default assignment settings for the latest version of the Quartus II software. The Pin Planner has been updated for the Quartus II software release version 15.0 You can now highlight transceiver clock multiplier unit (CMU) capable channels in the Quartus II Pin Finder. When creating a query, select Pin type in the Condition column, and CMU in the Value column. The CMU value is only available if your target device has CMU channels.
0 Comments
Leave a Reply. |
Details
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |